Bureaucrat, staff, administrator
4,335
edits
Changes
m
→Number of Blades
Like many aspects of ship design, designing propellers is a mixture of science and art in the form of experience. There is a lot going on at the stern of a ship that is poorly understood. This is not surprising. Every hull form, engine-propeller combination, interaction with the rudder wake region, and sea condition is different. Wave action introduces a random vertical moment into this equation.
For these reasons, most ship propellers operate at efficiencies around 56%, with the principle design problem being cavitation as rotational speed is increased. In comparison, aircraft propellers operate at 90% efficiency. On a ship a propeller efficiency of less than 50% indicates a poor propeller/hull design.[http://avstop.com/ Aviation Online Magazine] describes basic propeller principles. <ref>http://avstop.com/ac/flighttrainghandbook/basicpropellerprinciples.html</ref>
(Efficiency is measured as a ratio of the propulsive energy produced to the energy consumed in rotating the propeller shaft.)
With more blades, vibration and noise are reduced, and thrust is more evenly distributed. For example, a boat with 200 shaft horse-power and three blades has 66.6 hp per blade. With five blades, the power distribution is 40 hp per blade. With more blades, a propeller can be smaller. However, larger propellers are better at moving water. Small blades move less water. To compensate, they have to turn faster. But increasing rpm reduces efficiency. Other factors also come into play. For example, higher block coefficients in the hull design reduce propeller efficiency.
[[File:TrawlerPropellerRicePropulsion.jpg|thumb|350px|left|Adaptation by Rice Propulsion of the skewed design to a trawler – Photo with permission © Rice Propulsion, http://www.ricepropellers.com/]]
Again, like so many boat design issues, the optimum is a compromise between several factors. Generally, the choice is between large slow turning and small fast turning propellers with an increased pitch angle.
A double-screw boat is better with two smaller three-bladed propellers turning slightly faster. Propellers for nozzles should be square-tipped Kaplan designs. All propellers should be manufactured to ISO 484 Class 1 standards.
[http://www.vicprop.com Victoria Propeller Ltd.] has an [http://www.vicprop.com/displacement_size_new.php online calculator for propeller size] for displacement and semi-displacement hulls.
== Controllable Pitch Propellers ==
The pitch of a propeller can be fixed-true, fixed-variable, flexible or controlled. Think of pitch as the number of threads per inch on a screw.
Fixed propellers have a fixed (true) or variable pitch from the tip of the blades to the hub. A fixed-pitch propeller has a constant pitch at any radius from the hub to the tip. Think of this as a screw with a constant number of threads per inch.
A variable-pitch propeller has a pitch that increases from the hub to the tip, but is still fixed in the metal. Think of this as a variable number of threads per inch, i.e., the threads are getting further and further apart. Variable pitch propellers reduce cavitation and are used on high-speed boats, or on very large boats to compensate for varying inflow velocities due to the draft of the hull.
Flexible-pitch (pitch-adapting) propellers are made of a metal hub with carbon-fibre composite blades inserted. The blade pitch angle adapts as the load on the blade changes, reducing cavitation and increasing hydrodynamic efficiency by around 15%.<ref>A.I.R. Fertigung-Technologie GmbH, http://www.air-composite.com/englisch/html/unter/frameset_unternehmen.html</ref> Designed initially for high-end yachts, they are being tested starting in 2004 in larger sizes for the US Navy.
A controllable-pitch propeller has blades whose pitch angle can be adjusted mechanically while the propeller is turning. This requires a special hollow propeller shaft for the mechanical bits. This means the engine can run at its optimum rpm all the time. To speed up, or slow down, you change the pitch of the propeller. To go from forward to reverse, you simply reverse the pitch of the blades.
Controllable-pitch propellers yield the best overall fuel economy when vessel speeds vary. They are also an advantage in areas like Europe where fuel costs are higher. When vessel speed is constant most of the time, a fixed-pitch one is better because of the reduced complexity and cost.
== Kort/Rice Nozzles ==
When a blade rotates in water, it creates a high-pressure behind the blades and low pressure in front (towards the hull). This differential provides thrust. However, at the edge of the blades, high pressure leaks to the low-pressure side, resulting in loss of thrust.
[[File:KortNozzle.jpg|thumb|250px|left|Kort 19A Nozzle – note the smaller exit side – Photo with permission © Rice Propulsion, http://www.ricepropellers.com/]]
In the 1930s, this caught the attention of Ludwig Kort, an aeronautical engineer from Hanover. He developed nozzles (shrouds or ducts) for propellers. They prevented water from escaping from the blade tips. This improved propulsion efficiency at speeds under 10 knots.
Decreasing the exit side of the shroud, thus forcing the water to accelerate as it exited the propeller, made further improvements to the Kort nozzle. Eventually, several types of Kort nozzle were developed, with the Type 19 most suited to a trawler. Today, many companies make Kort Nozzles.
Later, the Mexican company [http://www.ricepropulsion.com/ Rice Propulsion] improved on the Kort nozzle by using aerodynamic duct shapes derived from wing sections displaying the highest lift and lowest drag.
== References ==
[[Category:PropulsionSystemsPropellers]][[Category:TrawlerDesign]]
