Bureaucrat, staff, administrator
4,335
edits
Changes
m
The provided [[#spreadsheet]] gives heating and air conditioning requirements in BTU/h (British Thermal Units/hour).
<div id="spreadsheet"><i>Download spreadsheet:</i> [tbd[HeatingCalculation|Calculating Heating Requirements]]</div>
Methods of calculating requirements for both heating and air conditioning tend to the arcane or the very simplistic. There are too many variables to consider, e.g., the colour of the deck paint affects the amount of heat gain inside. The provided [[#spreadsheetVentilationCalculation|Calculating Ventilation Requirements]] application tries to strike a balance between simplicity and accuracy. When calculating heating requirements, it ignores heat gain through southern exposure windows in the daytime and heat loss through all windows at night. It also ignores sporadic heat gain from equipment and appliances.
The spreadsheet uses the following formula to determine heating requirements in British Thermal Units per hour (BTU/h): <pre>BTU = V * T * K * B</pre> where: <pre>V = volume of the accommodation in cubic metres T = temperature differential in degrees Celsius K = dispersion coefficient (how heat ‘lossy’ is your boat) B = 4 (conversion factor to BTU)</pre> To calculate the Volume, for each living space multiply Length * Width * Height in feet as shown in the below table. Use judgement in deciding whether to list each space individually or as part of a section. The calculator will do the conversion to metric. For T, if you need to convert degrees F to degrees C, the formula is: <pre>C = (F – 32) * 5/9</pre> The dispersion coefficient K is adapted from housing construction as follows: <pre>K = 3.0 - 4.0 (Simple construction, simple windows - Not insulated) K = 2.0 - 2.9 (Simple construction, simple windows - Poorly insulated) K = 1.0 - 1.9 (Standard construction, double-pane windows - Moderately insulated) K = 0.6 - 0.9 (Advanced construction, triple pane windows - Well insulated)</pre> With K=3, the calculator yields 19 BTU/ft-sq while experts recommend 20 BTU/ft-sq, so we have good agreement at one end of the range. How aggressive you should get towards the other end is impossible to say. However, with the three heating systems specified for the boat there should be ample scope for increasing or decreasing the heat without upsetting the balance of the system. In a system that is under-sized, the furnace will run for long periods. In an over-sized system, the furnace will cycle frequently and run for very short periods. In general, a heating system should be sized 154% of the requirement so it runs at about 65% duty cycle. Typical furnaces are 80-90% efficient, so if you need 100,000 BTU output you will need one rated at, say, 125,000 * 154%. <table width="80% border="1"> <tr> <th colspan="5">Accommodation Space Calculation</th></tr><tr> <th>Area</th> <th>L<br>(ft)</th> <th>W<br>(ft)</th> <th>H<br>(ft)</th> <th>V<br>(cu ft)</th></tr> <tr> <td>Forward</td> <td> </td> <td> </td> <td> </td> <td> </td></tr> <tr> <td>Aft</td> <td> </td> <td> </td> <td> </td> <td> </td></tr> <tr> <td>Pilothouse</td> <td> </td> <td> </td> <td> </td> <td> </td></tr> <tr> <td>Salon</td> <td> </td> <td> </td> <td> </td> <td> </td></tr></table> == Air Conditioning Calculation ==A water-based chiller provides air conditioning. The chiller circulates chilled water through a water distribution system to the cabins, to cool them in summer. All pipes should be insulated to prevent condensation. (Similarly, if you opt for forced air, the ducts should be insulated.) The heat exchanger can be water-air or water-water. A water-air exchanger would have to work against the heat in the engine room, so it makes more sense to use a water-water heat exchanger with a keel cooler as a heat sink. This is overall more efficient (the temperature differential is higher with water), and avoids generating extra heat in the engine room. [[AirConditioningCalculation|Calculating air conditioning is more complex and so the answers are more varied. The next table gives three sets of estimates to illustrate the issue. Column A gives a series of BTU values derived from the buyenergyefficient.org web site <ref>http://buyenergyefficient.org/</ref>. Column B is based on an expert rule of thumb of 14 BTU per cubic foot, plus an extra 1000 BTU for good measure. Column C uses the spreadsheet calculator. Except for the last two data points, methods A and C are in good agreement, but make your own judgement. This spreadsheet calculator is adapted from Air Conditioning Your Home <ref>http://www.nrcan.gc.ca/energy/publications/efficiency/residential/air-conditioning/6051</ref>, published by the Energy Office of Natural Resources Canada (NRCAN) and available from its web site. It appears to fall within the general range of the other methods, based on area alone. Most rules of thumb are designed for single rooms, or two rooms joined. The author's calculator considers numerous more factors: * Number of occupants * Area of each accommodation * Area of windows and degree of sun exposure * Energy efficiency of windows * Shading of windows * Degree of insulation in the boat * Heat gain through the engine room bulkhead * Heat gain from AC machinery in the accommodation * Heat gain from DC machinery in the accommodationHeat gain from DC lights in the accommodation Several approximations were made in adapting the NRCAN model. For example, houses have a fixed position, allowing us to calibrate the different heat gain from windows facing any compass quadrant. Boats are mobile, allowing windows to face any direction at any time. The calculator assumes the worse case, with one full side of the boat having maximum southern sun exposure, the other minimum, i.e., it is moored east-to-west. The degree of insulation is set with the K factor in the heating calculation. The factor for heat gain through engine room bulkheads is a pure guess. The heat gain from AC and DC equipment is factored at 3.4 - 4.3, while NRCAN suggests 3.0 for AC appliances in a house. <table width="80%" border="1"> <tr> <th colspan="4">Recommended Cooling Capacity (BTU/h)</th></tr> <tr> <th rowspan="2">Area (ft<sup>2</sup>)</th> <th colspan="3">Method (ft)</th></tr><tr> <th>A<ref>http://www.energyefficient.org/</ref></th> <th>B<ref>Expert rule of thumb</ref><br>14 BTU/ft<sup>2</sup></th> <th>C<ref>Provided [[#spreadsheetRequirements]]</ref><br>Calculator (K=0.7)</th></tr> <tr> <td>100 – 150</td> <td> 5,000</td> <td> 3,100</td> <td> 3,465</td></tr> <tr> <td>150 - 250</td> <td> 6,000</td> <td> 4,500</td> <td> 5,775</td></tr> <tr> <td>250 - 300</td> <td> 7,000</td> <td> 5,200</td> <td> 6,930</td></tr><tr> <td>300 - 350</td> <td> 8,000</td> <td> 5,900</td> <td> 8,085</td></tr><tr> <td>350 - 400</td> <td> 9,000</td> <td> 6,600</td> <td> 9,200</td></tr><tr> <td>400 - 450</td> <td> 10,000</td> <td> 7,300</td> <td> 10,395</td></tr><tr> <td>450 - 550</td> <td> 12,000</td> <td> 8,700</td> <td> 12,705</td></tr><tr> <td>550 - 700</td> <td>14,000</td> <td> 10,800</td> <td> 16,170</td></tr><tr> <td>700 - 1,000</td> <td> 18,000</td> <td> 15,000</td> <td> 23,100</td></tr></table>
→Description
{{#TwitterFBLike:right|small|like}}
= HVAC Integrated Design =
This article works through the considerations in designing heating, ventilation and air-conditioning (HVAC) systems for year-round living on a 50-foot boat. Some of the concepts and calculations can also be applied to your next house.
The design is not optimal. When the furnace fails in the coldest weather there is a heating shortfall of 21,560 BTU or 6 kilowatts (kW).
=== Description ===
The HVAC system uses a blend of loosely coupled systems to provide maximum energy efficiency and redundancy for a year-round live-aboard. Fresh-air ventilation uses small zone-based air vents but this makes humidity control difficult. The heating and cooling systems use a shared circulating-water distribution system to minimise bulkhead pass-throughs. Heating is by a diesel furnace with backup from a diesel fireplace. Cooling is by a chiller with keel cooler, with backup from the cold-plate refrigeration system. Hot water is heated by the engine, the diesel oven, a [https://en.wikipedia.org/wiki/Solar_thermal_collector solar collector ] or AC elements using shore power or the house bank.
[[File:blendedHVAC.png|thumb|400px|left|The heating, ventilation and air-conditioning are a blend of loosely coupled systems to provide maximum energy efficiency and redundancy]]
Hot water is heated in several ways. In port in summer, the water is heated by standard electrical elements operating off the alternating current (AC) system. In winter, it is heated by the water jacket on the diesel oven. If the oven is not in use, and there is no other source of heat, the hot water tank defaults to the electrical elements.
Use an anti-scald, balanced-pressure shower valve (not a tempering valve!) on the showers to regulate the water to 120 Fahrenheit (F°F) 48.8 Celsius (C°C). This will avoid scalding people, and reduce water consumption. Bathers will be able to mix the water faster to a comfortable temperature.
=== Refrigeration ===
== Control Zones ==
For heating, ventilation and air-conditioning distribution and control purposes, the boat is divided into the zones in the below table. With a K=1(see [[HeatingCalculation|Heating Calculation)]], the boat requires approx. 37,810 BTU/h of heating. The main diesel furnace supplies this, sufficient for the coldest weather.
<table width="80%" border="1">
</table>
But what happens in an emergency? In the event the furnace fails, the Bristol Pacific model diesel stove in the galley can provide 6,500-16,250 BTU to heat the forward accommodation. At the lower heat setting it could maintain a temperature differential of 21 C°C, while the higher one maintains the design differential requirement of 55 C °C in the forward compartment.
At the lower setting, water pipes, etc., are protected down to -20 C°C, a not infrequent winter temperature, which is why the design requirement is the higher 55 C °C differential. Because the galley stove alone cannot heat the whole boat in the event of a furnace failure, additional heat has to be supplied by the diesel fireplace in the salon. A fireplace such as the Bubble produces only 3.5 kW (11,946 BTU), good for a 17 C °C differential overall. So it will only heat the pilothouse and salon, not the aft cabin.
Therefore in an emergency in the coldest weather we have a heating shortfall of 21,560 BTU (6 kW). This is not critical above deck in the salon and pilothouse, since there are no water pipes there. But it is critical in the aft head.
Finally, some heating has to be provided to the engine room to keep water tanks and pipes from freezing. Obviously some further development is required in the design of the back-up heating. Increasing the output of the diesel stove is not a good option, as this would tend to make it less useful as a cook stove. Perhaps the Bubble should be re-located to the aft cabin, but this negates its lifestyle purpose. More practical solutions are to shut off the water to the aft head and run the engine to keep the engine room warm. Another solution is to have an aft engineroom and a contiguous forward accommodation space.
== Heating Calculation Related Pages ==
== References ==